Name: Air Nipper, Cutting 2.6mm Copper Wire
Brand: Tool
SKU: 1157
Availability: InStock

Air Nipper, Cutting 2.6mm Copper Wire

Size chart

Clothing Size Conversion Chart
Category	US	EU	UK	Chest (in)	Waist (in)	Hips (in)
Men	XS	44	34	32-34	26-28	33-35
	S	46	36	34-36	28-30	35-37
	M	48	38	38-40	32-34	39-41
	L	50	40	42-44	36-38	43-45
	XL	52	42	46-48	40-42	47-49
Women	XS	32	6	31-32	24-25	33-34
	S	34	8	33-34	26-27	35-36
	M	36	10	35-36	28-29	37-38
	L	38-40	12-14	37-39	30-32	39-41
	XL	42	16	40-42	33-35	42-44
Youth	XS	128	7	26-28	23-24	26-28
	S	134	8	28-30	24-25	28-30
	M	140	10	30-32	25-26	30-32
	L	146	12	32-34	26-27	32-34
	XL	152	14	34-36	27-28	34-36

Pants Size Conversion Chart
Category	US	EU	UK	Waist (in)	Hip (in)	Inseam (in)
Men	28	44	28	28	34	30
	30	46	30	30	36	31
	32	48	32	32	38	32
	34	50	34	34	40	33
	36	52	36	36	42	34
Women	0	32	4	24	34	30
	2	34	6	25	35	30
	4	36	8	26	36	31
	6	38	10	27	38	32
	8	40	12	28	40	32

Shoes Size Conversion Chart
Category	US	EU	UK	Foot Length (in)
Men	6	39	5.5	9.25
	7	40	6.5	9.625
	8	41	7.5	10
	9	42	8.5	10.25
	10	43	9.5	10.625
	11	44	10.5	11
	12	45	11.5	11.25
	13	46	12.5	11.625
Women	5	35	2.5	8.5
	6	36	3.5	8.875
	7	37	4.5	9.25
	8	38	5.5	9.625
	9	39	6.5	10
	10	40	7.5	10.25
	11	41	8.5	10.625
	12	42	9.5	11
M (Unisex)	5	37	4.5	8.75
	6	38	5.5	9
	7	39	6.5	9.5
	8	40	7.5	10
	9	41	8.5	10.25
	10	42	9.5	10.625
	11	43	10.5	11
	12	44	11.5	11.25

58 People watching this product now!

Good price air scissor, used for shearing copper/ iron/ soft stainless steel wires. Aircraft aluminum body, compressive and durable, safer to use than normal hand-held scissors. 230cm³/cycle air consumption, 73-87psi operating air pressure.

Specification

Model	T-HS20-S5
Maximum Cutting Capacity	2.6mm Copper Wire 2.0mm Iron Wire 1.6mm Soft Stainless Steel Wire
Air Consumption	230cm³/cycle
Operating Air Pressure	73-87psi
Applied Pressure	1370N
Air Inlet Size	3/8 Inch
No Load Speed	800rpm
Frequency	50Hz
Applicable Hose Size	5*8mm
Overall Length	195mm
Net Weight	0.49kg
Package Weight	1.2kg

Details

	A. overall length: 95mm
	B. thickness: 12mm
	E. working length of blade: 22mm
	F. working angle of blade: 30°
	G. V-shaped upper end: 8mm
	H. V-shaped bottom end: 4mm
	I. maximum width of knife arm: 27mm
	J. maximum thickness of knife arm: 12mm
	K. minimum thickness of knife arm: 1mm
	L. front end length of screw hole: 34mm
	width of closed shear: 24mm
	extending length: 26mm

Installation of air nipper blade

Put the blade into the air nipper body.
Align the bolt and put it in.
Tighten the nut.

Tips: What should you pay attention to when using an air nipper for cutting copper wire?

Note that the pneumatic air nipper should use the working pressure within the specified range (73-87 psi). If the working pressure is too low, it will affect the cutting ability of the air scissor blade. If the working pressure is too high, it will easily cause damage to the air scissor blade and rupture of the internal piston of the pneumatic scissor.
The center screw between the blade of the pneumatic nipper body is made of special material, so no substitutes can be used instead. Or it will result in “reaming” of the screw holes of the pneumatic nipper body and cause damage to the blade of the pneumatic nipper, and the pneumatic nipper body cannot be used again after reaming.
Do not use air cutters to cut copper wires that exceed the maximum cutting capacity of 2.6 mm.
Turn off the air pressure before replacing the blades of the air nippers, and avoid “invalid cut” of the air nippers.
Avoid falling of the pneumatic nipper body and blade.
Do not refit the air scissor blade at will, so as not to reduce the service life.